...

When things start going wrong, you begin to wish that you had a copy of ALL your important files. The trick here is ALWAYS make sure that you have a copy of your IMPORTANT FILES always. You never know when your Z88 may go wrong (if at all) or even if you may make the occasional deliberate mistake.

FLASH CARDS 

The simplest way of doing this now is to have a couple of Flash cards and USE THEM.

...

The important thing is that you have a copy of your files. See 'Using two Flash cards.'

The original EPROM Packs - no longer recommended.

Then there are several ways you can store the data as well as or instead of EPROMS. You could just use EPROMS while you are out and then one of the backups when you get home or back to the office.

Computer Links

If you have a Computer with a disk drive, - this is the most cost-effective way of storing the files from your Z88. There are many computers that can be used with the Z88. Check with your Z88 dealer what is available. You will be surprised at the number of third party vendors who have written links for the Z88.

Eazylink2 is the version supported on this site.

Cassette Tape - no longer recommended.

If you are on a tight budget and haven't got another computer then Z-Tape is the next `best thing' to use. Using this program you can store your files onto your cassette tape recorder. It is SLOW and depending on which Tape Recorder you use, it can be unreliable. Cassette tapes have been used on several computers in the past. It was a cheap way to store data when there were cassette tape recorders around, but they were not the most reliable.

Disk Drive - no longer recommended.

Undoubtedly the best way to store files was with a Disk Drive. The market leader was the RangerDisk which produced PC compatible 3-1/2" disks. It was expensive, but once you've paid the initial cost of the drive, disks were cheap and reliable. There are other disk drives for the Z88 which are cheaper, but these do not produce disks that can be read by other computers. If these disk drives go wrong, you would not get the files stored on your disks back until the drive was repaired.

Use either a computer link or a Flash card now as these are more cost effective now in the 21st century.

Instructions for installing and using cartridges

RAM and EPROM

(Cambridge Computer leaflet)

There are two types of cartridges RAM and EPROM.

EPROMS are designed to function in slot 3, and RAM cartridges Preferably in slots 1 and 2. They will work in slot 3 but they will take more power from the batteries and you will not be able to use EPROMs.

The perspex cover on the front edge of the Z88 is hinged and if gently pulled from the top, will open enough space to allow you to insert your card(s). When you have inserted a card, with the label on the card facing the underside of the keyboard, then push the perspex flap back into position, i.e. fully closed.

IT IS EXTREMELY IMPORTANT TO REMEMBER THAT ONCE THE FLAP IS OPENED AND A RAM CARTRIDGE IS REMOVED, THEN YOU NEED TO RESET THE MACHINE, SEE PAGE 8 OF THE USER GUIDE. THIS WILL CLEAR ALL YOUR DATA IN THE Z88, i.e. 'RESET CLEARS MEMORY. THEREFORE, ONCE YOU INSTALL YOUR RAM CARTRIDGE, DO NOT REMOVE IT.

SIMILARLY, IF YOU PURCHASE A RAM PACK AND INSTALL IT AFTER YOU HAVE BEEN USING THE Z88 FOR A WHILE, YOU ARE STRONGLY ADVISED TO BACKUP ALL YOUR FILES ONTO AN EPROM CARTRIDGE FIRST. THE REASON IS THAT IN ORDER TO RECOGNISE THE EXISTANCE OF NEW MEMORY THE COMPUTER HAS TO BE RESET, THUS ERASING EXISTING MEMORY.

One other thing to remember is that RAM cartridges draw their power from the Z88 While the Z88 is on or in a sleep mode, your data is safe. If the Z88 is deprived of power (see pages 6 and 7 of USER GUIDE) then your RAM is also deprived of power, and will lose its contents.

REMEMBER that your EPROM Cartridge is the best method of archiving your valuable data files or programs, but once the EPROM is full, the recommended way to erase it (if required) is to me the UV EPROM ERASER from Cambridge Computer Ltd.

Now refer to page 74 of your User Guide at The Filer section on how to use your EPROM

Using RAM PacksImage Modified

When you put a RAM pack into the Z88, it good practice to give your Z88 a HARD RESET.

If you are using a 1M RAM pack it is imperative that you do this as when the Z88 was designed, there were no 1M RAM packs to test it, so OZ (the Z88's operating system), sometimes doesn't recognize it correctly.

To check whether the Z88 has recognized it, you need to select the INDEX and then Image ModifiedCARD.
The correct amount of RAM should be properly displayed, i.e. 1024K for the 1M RAM pack.
If it doesn't show this, you should do another HARD RESET until the Z88 recognises the right size!

EPROMs

The Header on EPROMsImage Modified

After Erasing an EPROM, all information on it is removed including what is called the Header.

The header is a few numbers that go at the start of the EPROM to tell the Z88 what it is.

See Inserting EPROMs.

The header is blown into the EPROMS when it is

...

It is a good idea to catalogue EPROM after erasing it, so the Z88 knows that it has an EPROM and which size it is before saving files to it.

Trouble erasing EPROMs

Sometimes an EPROM does not get erased completely because of a speck of dust on the glass casting a shadow onto the chip. Tapping the EPROM to remove the dust does the trick.

...

Using ROMcombiner is a safe way to check if the EPROM is empty and blowing ROMs.

Inserting EPROMs

You can insert and remove EPROMs any time providing you are not `Saving to EPROM' or `Fetching from Eprom.'

See Check Z88 Cards.

Removing ROMs Image Modified

 To remove ROMs,

1. Go into the INDEX.
2. Check that you have not got the program still running (it will be shown as a Suspended Application with a Slot number at the end if it is). If it is running, you should move the cursor over the program in the Suspended Applications and KILL it/them.
3. With the Z88 still turned on, open the card flap. The Z88 should bleep.
4. Remove the ROM card and
5. Close the flap.

...

For additional information click here. 

Cannot Satisfy Request or No room

This message appears when you are trying to Save a file to EPROM and it is FULL

or because the header of the EPROM has become corrupt. See Bugs - EPROM 256K.

Corrupt ROM or EPROM

There is a known problem with EPROMs (or ROMs if an EPROM is used). If you insert a new set of batteries into the Z88 while an EPROM or EPROM-ROM is in Slot 3, it can get corrupted. This is because Slot 3 is the only slot that has a write line that is used when saving files to an EPROM.

...

Before erasing the EPROM (which will allow you to use it again), check to see if you can recover any of the files using Fetch from EPROM.

Are you using a ROM or EPROM?

EPROMs can be used as ROMs. This can confuse users as it might say 32K EPROM on the pack, but it might be used as a 32K ROM for additional applications.

...

and see what the Z88 tells you what you have got in the slot.

Change Use of ROM or EPROM

You can change the use of EPROM or ROM that you do not need to use anymore. For example, if you had a Mac Link ROM and you are now on a PC and no longer need it you can do the following.

...