There are two ways to upgrade your Flashcard
See Prerequisites
If you are going to blow the image into an EPROM card, start erasing it now, as it may take several attempts to erase it completely. |
The Z88 needs to have the following cards as a minimum configuration.
The alternative temporary solution is to use the Flash card that OZ will be loaded into. The Z88's configuration is either the 512K/512 RAM/Flash option:-
or the 512K RAM (minimum)/1M Flash option:-
Download from the Wiki the files needed to transfer to the Z88. If they are zipped, unzip all the files on the Desktop Computer and save them all in a separate directory.
Download Location | ||
---|---|---|
Eazylink | FlashStore | |
Eazylink 5.2.3-06 | Flashstore 1.9.3 | |
Files Required | eazyLink.63 | flashstore.63 |
Imp/Export | 4 minutes 10 seconds |
For convenience This section has been copied from the Eazylink2 User Guide to show how to do this.
The first time Eazylink is connected to the Z88 the Com Port window is displayed.
An intelligent guess is made at which Serial Port is being used. Here is your chance to check that the correct one has been selected. In this case Windows is using COM 5.
Getting control of Eazylink can be difficult to do initially because Eazylink2 is expecting the pop-down to be running on the Z88. Just keep waiting until you receive the Reading Z88 Devices Command Failed Command Error window.
Choose 'Ignore.'
What you really need to see is the top Eazylink Menu not being greyed out
Here is a picture of the blank screen you should see. The left-hand window (normally used to show the Z88 side) is not used in this Imp-Export Mode. The right-hand side window showing the Desktop side is used. Select which Directory is to be used here. The selection of the files are made in a different window later.
These should automatically be un-ticked when using Imp/Export.
If you get problems, as the Eazylink popdown is not being used, all the tick boxes are to be cleared.
On the top menu bar, Select Settings
The Com Port details will be displayed.
On the top menu bar, Select Settings
The Com Port details will be displayed.again but this time select the Translations Tab.
Clear both tick boxes and click OK.
On the top menu bar, Select Settings
The Com Port details will be displayed.again but this time select the General Tab.
Clear all EazyLink tick boxes and click OK.
On the top menu bar, Select Z88
Communication not established
If all the functions are greyed out in the Z88 Menu, communication to the Z88 has not been established. Check that the cable is connected to the Z88 and Connect the Z88 to the Desktop has been followed.
If 'Show Details...' is selected, you will be presented with a help screen listing instructions (without the screen shots) on how to use the Z88.
On the Z88 it is a good idea to make sure you have additional RAM in slot 1 and Resetting the Z88 before starting this exercise unless you want to keep the files that are already on the Z88.
Use S
Change Default device to :RAM.1 - You need extra RAM in your Z88 for the file and it needs to be in slot 1.
Check that the Transmit and Receive rates Parity (9600) and change the default Xon/Xoff settings from (Yes) to (No) are the correct value as given.
Scroll down to the next instruction.
Use X
Scroll down to the next instruction. 3. the Imp-Export Menu will be displayed
by pressing 'b' and then press the key.
On the Desktop, click 'Yes' to 'Is Z88 ready?'
The Desktop will now display a window for you to select which file(s) to send
Mark the desired files. These are:-
Download Location | ||
---|---|---|
Eazylink | FlashStore | |
Eazylink 5.2.3-06 | Flashstore 1.9.3 | |
Files Required | eazyLink.63 | flashstore.63 |
Select the Z88's destination storage slot (in this case Slot 1).
After press OK the Z88 screen will show
Using remote name: :RAM.1/the_filename
(Incrementing numbers on this row)
End of file
This will repeat itself until all the files are transferred.
Press on the Z88 to return to the Imp-Export Menu.
Both these popdowns are 16K each. Might as well put both of them on the same card and use up the spare space if only Eazylink is used. |
The files are shown here displayed in the Filer are:-
To run the program, do the following:-
The following screen is displayed.
EPROMs can only be programmed in Slot 3.
Press V. followed by
If the EPROM is properly erased the following screen is displayed.
If an error message is displayed,
the EPROM should be removed and erased again with the EPROM Eraser until it passes this test.
There is no point in checking whether it is erased or not, it can be erased here straight away.
Press F. followed by
To return to the main display.
Press 0 .
Follow the instructions as above, except the Flash card is in Slot 1.
Press F. followed by
To return to the main display.
Press 0 .
Press C. followed by
Press C. for Create followed by
Destination card name? EAZYFLASH
Delete source images (Y/N)? N
From the main screen, Select
The screen will flash a few times until the following screen is displayed. If any programming errors are given, the EPROM will need to be erased and this procedure needs to be repeated from Verify EPROM banks properly erased.
From the main screen, Select
The screen may flash a few times until the following screen is displayed.
This is similar to Blow image files to Flash Card (Slot 2) except to select Slot 1.
From the main screen, Select
The screen may flash a few times until the following screen is displayed.
If the 512K/512K Flash/RAM is in Slot 1, do a HARD RESET, otherwise
To run Eazylink either select the INDEX with I or
or move the cursor over the application name and press .