Introduction
EPROM Programmers come in different sizes and are designed to program individual chips with
- 32 pin
- 40 pin
- 48 pin
The 40 and 48 pin programmers are able to program larger memory devices as they have more address lines available. Allowing the user to manually set are now software controlled. This works well if the chip type and footprint is in the database but what happens when a variation is required?
This break out card allows the user to set in hardware, a source footprint to be translated into a target footprint, using either switches or jumper leads. Larger memory devices that are not be supported may also be programmed, by manually setting the most significant bit individual address signal lines using lines to a 1 or 0 using the tri-state switches , allow these provided. This allows larger devices to be programmed by in several steps using a 32 pin programmer.
- different footprints that either
- plug in directly
- or use additional adapters
before connecting to the ZIF zero-insertion sockets supplied with the programmer. In some cases the physical chip or the footprint is not always available. In some cases the physical chip or the footprint is not available. The user may know, for example, which signals need to be swapped, changed or held at a different logic level and would welcome a board to try different combinations before the final solution is found, either be theory or by trail and error.
The source 48/40/32 pin ZIF header fits into the EPROM programmer.
Space is provided for the target size ZIF sockets if required.
- 32 pin
- 40 pin
- 48 pin
Additional tri-state switches are provided to take up the job that some adapters do holding chip select pins, for example, when the number of active pins from the programmer is at a premium.
In the case of some older 8-bit game computers and the Z88 card for example, the flash or EPROM chip is inside a plug-able module. The address and data lines are then only available via a bespoke connector.
The user may know which signals need to be swapped, changed or held at a different logic level and would welcome a board to try different combinations before the solution is found, either be theory or by trail and error.
The objectObject
of this card is to design a PCB that can be used in a variety of ways depending which components are fitted This allowis allows the user to have full hardware control of the signals by selecting switches for testing, or making permanent changes by using wired links.
The lever that grips the chip can either be at the top left-hand side or the bottom right-hand side of the ZIF socket. The L shaped card is designed so that it does not fowl the this lever.
Design
The design of the card is split in 3 parts where the first and last parts are similar and the middle part translates the desired signals.
Gliffy | ||||
---|---|---|---|---|
|
Source - Plug to fit into the ZIF socket of the EPROM programmer
- Address Tri-state switches
- Header for additional address lines for Willeim programmers
- Space for 2 off 24 pin headers to be used for 48 pin programmers.
Shorter lengths may be fitted for the smaller sizes of programmers. - These headers are repeated if required for jumper wires are used to connect directly to the output.
- Tracks are marked with a section that allows them to be permanently cut.
- Another row of headers if required, may be fitted the other side of these cuts, so that the tracks may be reconnected using header links.
Translation Section
- 2 x 12 way DIP switches to select the footprint for the source and destination devices
- Tri-state switches to statically select the state of individual pins e.g. Chip Select
Target - 48 pin ZIF Socket - Additional connector
- This allows up to the a maximum size 48 pin zif socket to be used.
- The headers are repeated so that jumper wires may be used.
- Tracks are marked with a section that allows them to be permanently be cut.
- Tracks may be reconnected using a header link
- 50 pin IDC connector to allow connection to non standard external cards
- Z88 external card socket connector
Parts List
Description | Qty | Order Code | Min Qty | Price |
CONNECTOR, HEADER, THT, 2.54MM, 50WAY | 2 | 109-6994 | 1 | 2.47 |
SOCKET IC, ZIF, 48WAY | 1 | 1 | 13.09 | |
HEADER, 2.54MM, THT VERT, 24WAY | 6 | 5 | 2.84 | |
CRIMP LEAD, SKT, MICRO-FIT, 150MM | AR | 5 | 1.67 | |
JUMPER SOCKET, BLACK, 2.54MM, 2WAY | AR | 10 | 0.18 | |
HEADER, VERTICAL, 0.1", 8WAY | 1 | 588-775 | 5 | 0.28 |
HOUSING, 26AWG, 8WAY | 2 | 109-8717 | 5 | 0.46 |
RIBBON CABLE, IDT, 8WAY | 1 | 30m | 69.01 | |
SWITCH, DIL, SLIDE, 12WAY | 2 | 1 | 1.87 | |
SWITCH, DIL, TRI-STATE, 10WAY | 1 | 1 | 0.32 | |
RESISTOR, CARBON FILM, 2K2, 0.25W, 5% | 2 | 50 | 0.02 |
Circuit Diagram
The circuit diagram of this card can be viewed by clicking here (which will open in a new window).