Programming different Cards
On the previous EPROM Programmers, the footprint could be set independently from the device. This is no longer the case.
The 1M chip connections are as follows:-
34 WAY CONNECTOR Z88 CARD | |||||||||||||||
LINK | |||||||||||||||
34 WAY CONNECTOR PROGRAMMER | |||||||||||||||
DIL FUNCTIONS 256K EPROM | |||||||||||||||
DIL FUNCTIONS 512K FLASH | |||||||||||||||
PIN OUT OF 32 PIN HEADER | |||||||||||||||
PROGRAMMER ZIF 32 & HEADER | |||||||||||||||
TSOP 40 Functions | |||||||||||||||
1 | 1 | A19 | A19 |
| NC | A20 | |||||||||
2 | 17 | /WE | 31 | A18 | A18 | NC | A21 | ||||||||
A17 | 30 | A17 | A17 | /WE | /CE | 22 | /CE | /CE Vpp | |||||||
A16 | 2 | A16 | A16 | /OE | /OE | 24 | /OE | /OE | |||||||
A15 | A15 | 3 | A15 | A15 | RY/BY | ||||||||||
A14 | A14 | 29 | A14 | A14 | D7 | D7 | 21 | D7 | D7 | ||||||
A13 | A13 | 28 | A13 | A13 | D6 | D6 | 20 | D6 | D6 | ||||||
A12 | A12 | 4 | A12 | A12 | D5 | D5 | 19 | D5 | D5 | ||||||
9 | 2K2 | 20 | /CE | D4 | 18 | 18 | D4 | D4 | |||||||
Vcc | Vcc | 32 | Vcc | Vcc | Vcc | Vcc | 32 | Vcc | Vcc | ||||||
NC | Vss | Vss | 16 | Vss | Vss | ||||||||||
/RST | Vss | ||||||||||||||
A11 | A11 | 25 | A11 | A11 | D3 | D3 | 17 | D3 | D3 | ||||||
A10 | A10 | 23 | A10 | A10 | D2 | D2 | 15 | D2 | D2 | ||||||
A9 | A9 | 26 | A9 | A9 | D1 | D1 | 14 | D1 | D1 | ||||||
A8 | A8 | 27 | A8 | A8 | D0 | D0 | 13 | D0 | D0 | ||||||
A7 | A7 | 5 | A7 | A7 | A0 | A0 | 12 | A0 | A0 | ||||||
A6 | A6 | 6 | A6 | A6 | A1 | A1 | 11 | A1 | A1 | ||||||
A5 | A5 | 7 | A5 | A5 | A2 | A2 | 10 | A2 | A2 | ||||||
A4 | A4 | 8 | A4 | A4 | A3 | A3 | 9 | A3 | A3 |
A pull down resistor is fitted on the Z88 Card side of the connector to ensure it is selected.
The switch is glued to the board to swap the A18 and /WE signals. Footprints are hardware selected.
1M, 512K Flash v EPROM Chips
The difference between the pin-outs of the 512K Flash and EPROM chips are
The differences in the footprints are:
- Vpp
- A18
- /WE
1M Flash & EPROMs
32 Pin EPROM Programmers program up to 512K devices. This switch allows the 1M Flash Card to be programmed in 2 halves.
The switch positions are used to program:-
- DIL 512K HIGH (normal) - 512/512K Flash / RAM cards and the top half of 1M Flash cards with 32 Pin Programmers.
- DIL 512K LOW - the bottom half of 1M Flash cards with 32 Pin Programmers.
- TSOP40 1M Flash - with 40 pin Programmers or EPROMs up to 256K EPROMs
Switch Card Details
Modification to Z88 Extender Card
- The card is cut so that the unused part is removed. This enables the lights on the EPROM Programmer to to seen.
- 4 tracks (1, 2, 9 and 17) from the 32 pin header are cut in-between the 2 off 34 way connectors and a 4 pole 3 way switch is used.
- 2 off 2K2 resistors are connected from pin 9 on the Z88 card side and pin 2 on the switch to pin 20.
- The holes of the 2 off 34 way connectors are used to connect to the switch.