About Aviation Tools

AVIATION SOFTWARE TOOLS 1988

Colin Marshall, Ian Green Mathon Road, Malvern Worcestershire, WR14 4BU

I was given a copy of Pilots Companion and the manual in 1989 to evaluate. Did anyone use it? Was it well marketed? I never heard of it again.

The company was based in Malvern, their address was P.E.I. P.O. Box 4 MALVERN Worcs., but they are no longer there. So here is your chance to trawl with me through the commands and get an understanding what this program did.

Pilots Companion

Download

OZvm snapshot

OZvm snapshot2

OZvm OZ4.5 B4 Slot0

This applications needs 32K of either EPROM or Flash space.

Introduction

Pilots Companion by Aviation Software Tools is written in BBC BASIC for the Cambridge Computer Z88 portable. It is a Flight Planner for Pilots.

It has several 'built-in' databases with Airfields, NDB, VOR. The user is invited to create, append,

The standard MENU and HELP facilities are not used in this application. The user will need to read this manual first to get a good overview of the product before use.

Menu

Pressing the MENU key reveals 'no topics.' The Menus are in the main program itself.

Here you can obtain either your required descent rate from a given distance to run or give your required descent rate. The program will tell you when to begin the descent.

F. Starting the program on the Z88 Computer.

Pre-Flight Requirements

The requirements to run this program on the Z88 is at least 128K RAM in slot 1 and the Pilots Companion EPROM to be in slot 3. The EPROM may be moved after running the program.

For best results, (if you have nothing running on the Z88)  Pilots Companion can be started initially by giving the Z88 a Hard Reset, with the Pilots Companion's EPROM card in slot 3. The boot.cli file starts a chain of commands that sets  :RAM.1 as the Default Device, fetches all the files from the EPROM card and starts running the program. This ensures that the Z88 is at a known state. To leave the program press the  key. Alternatively use the following methods depending what state the Z88 is in.

1. If Pilots Companion is already shown in the index list of running Applications.(Press to view).
    
2. If Pilot Companion has already been used it will appear in the SUSPENDED ACTIVITIES area of the index from which it can be re-selected using the cursor bar. 

   

   When it is running, when in the INDEX it will be shown as a suspended activity with the file name used as YOUR REF.  There can only be one Pilots Companion application running

   Position the cursor on the name & press
   
   

3. Pilots Companion files are resident in the computer having been loaded from the plug in EPROM cartridge but not shown in the index list of running applications.(Press F to view Files - the main program is called 'way2').  Enter BBC BASIC and type RUN "WAY2"

   Note that if the program returns to the BASIC prompt at any time then typing RUN will start it again.

4. Pilots Companion is on EPROM and your computer is in use
   
   A 

   Note the following procedure will delete any running applications so first save any required information to files.

   Plug the Pilots Companion EPROM into slot 3 on the Z88. Ensure Slot 1 has at least 128K of RAM Plugged in..'
   Press, the Diamond key () and then type PURGE
   The required files will, now be loaded from EPROM this will take a little time finishing with the Pilots Companion first menu being displayed.
   The EPROM may now be removed and from now on methods 2 or 3 above can be used to start the program. Most pilots will want to leave the Pilots Companion resident as updates to preserve temporary updates.
   
   B Alternatively fetch the file boot.cli from the Pilots Companion EPROM and Execute the file. This will then load all required files and start the program.
    

5. Pilots Companion is on EPROM and your computer is new.
   
   Plug the pilots companion EPROM into slot 3 on the Z88. Plug 128K RAM pack into slot 1 on the Z88.
   Press the  Diamond key (), then type PURGE (This is the same as pressing the reset button),

If required all files from EPROM could be copied-manually then 2 above actioned.

G. A Brief description of the General function of the Flight plan

A plan is developed beginning with the new plan option (opening menu option 2).

Once this plan has been completed it becomes the current plan (option 1 of the opening menu). Actions on the current plan are taken from this option i.e. to re-run the plan and maybe change wind, airspeed etc. to print, to run the return trip, to save this current plan.

Old plans saved from previous use may be recalled and become the current plan. These old plans are retrieved using option 3 of the opening menu.
A most useful feature of this program is the ability to restart at any time this is achieved by pressing the key on the top left hand corner. (Commonly known as the OH! shit button). This allows you to play with features ad hoc and end recover at any time. The best way to find out how it works is to keep pushing buttons - it’s really very easy.

Once you find out how easy it is to generate a plan you will never want to revert to the old manual planning methods.

H. More Detail on NEW PLANS

- (select option 2 on the opening menu). The following appears on the display

ENTER POINT OF DEPARTURE?

The above message is displayed on the screen. Ensure that is selected then type in the full name of the airfield from which you wish to begin your journey. Press the  key and the computer will then begin to search for the place name you have typed in. When the place name has been found the message requesting you to enter the next point in your flight is displayed i.e.

ENTER WAYPOINT NO.1 ?

.
Remember you can press to restart everything if you wish this will return to the opening menu.

VOR HON

The space between VOR and the ident HON must be included. For an NDB use the same format i.e.

NDB SVN

ENTER WAYPOINT NO 1?

This is displayed if the search for your place name was successful. Now type in your next point in the journey i.e. the first destination point. Press  and the search for this place will begin
Note: - If you are still at the initial stages of learning how to use PILOTS COMPANION then use another airfield name at this stage in the game to speed the production of your first plans. (You can find out how to enter and save self-derived points later on in this manual.)

If the search for WAYPOINT NO.1 was successful then the message

ENTER WAYPOINT NO.2 ? 

will be displayed.

To end your plan press  at this point or continue the plan by typing in more waypoints as described above. Pressing  at the ENTER WAYPOINT NO. message will indicate there are no more points.

The plan routing is now displayed giving the Latitude & Longitude of each place along with its It letter identifier, (if there is-no identifier then the first It letters of the name are used in the case of airfields.) You may hold the display by pressing  to inspect the plan and verify the information provided is correct. To continue the program press  again.

In either case the details menu is now displayed as follows :-

ARE THESE CORRECT ?

If the details are correct then press  (or Y and press )

The details will then be used as given to generate the plan. From this point the whole flight plan is produced automatically the displays running through each stage without further manual input. If you wish to hold the display at a point then press  - the screen will now be held until  is Pressed again.

The final screen after the last Waypoint and destination are displayed gives details used to produce this plan along with total distance, total time and total fuel used. This display may also be held using  as described. The program returns to the opening menu after this display.

The plan you have just completed now becomes the current plan and if option 1 on the opening menu is selected then the current plan menu is displayed This gives options to display the current plan again giving you the opportunity to change the details -wind etc. required or simply repeat the plan again.

Other options are to produce the return trip plan -this is generated automatically by selecting this option. Printing the plan to a paper printout can be from this menu. The plan may also be saved for future recall here.

Further operations on the DETAILS menu - if the details as shown on -the display at the point indicated above were not correct then type N and press ENTER. The alter details menu is now displayed.

The values shown inside the brackets at each menu line are the default values and pressing  will give this value. To alter a value simply type in the required number followed by . Follow the instructions as given in the display.

Now follows a description of the display.

1. The display is -split into 2 columns. The left hand column contains the highest priority information the topmost being your required heading. 
   The right hand column contains lower priority information but will still be useful en-route.
2. The following words appear on this display.

The left hand column contains:

The right hand column contains :

At the end of the plan-the following are displayed the left hand columns showing the values of windspeed and direction, airspeed, fuel consumption and magnetic variation used in the current plan computations.
The right hand side columns give totals of Distance, time and fuel used for the complete trip. The printed version of the plan is also timed and, dated at the time of printing.

9) Returns automatically to the opening menu.

2 New Plan - Example

Select 2.

Point of departure OXFORD is found. NORTHLEACH ROUNDABOUT is not.

The four choices are:-

(1) Re-enter name of 'This waypoint'

Enter a different name.

(2) Enter position of 'This waypoint' by Latitude & Longitude

See Defining Waypoints for more details.

(3) Enter position of 'This waypoint' by Relative Location

See Defining Waypoints for more details.

(4) Exit to Main Menu

The program returns to the Main Menu.

Select (2) Enter position of 'This waypoint' by Latitude & Longitude

** BRIZE NORTON
0,51:50.250N,001:50.150W,0F,W,000 A40 NORTHLEACH ROUNDABOUT VRP
** BRIZE NORTON (ENR 2.1)

Enter Latitude and Longitude.

Select Y when the data is correct.

Enter another new way point for Kemble.

No more way points, press  to continue,

To check headings, no wind data ia entered,

DESCRIPTION OF MENUS and THEIR OPERATIONS MAIN MENU

Main Menu

To select a function on the menu, select the number that is required.

1 CURRENT PLAN

Selection calls the following menu :

Selecting current plan gives four further choices. This means that a New Plan needs to be made before using this function.

5 REPEAT CURRENT PLAN

Selects the currently resident plan and runs through it. It is possible to change details such as airspeed, wind, magnetic variation 1 etc. during this operation when requested if required.

5 Repeat Current Plan - Example

Check the route

Enter the current wind (no wind calculations as default)

Current route.

Look at the same route with wind calculations. 5230N 0230W @ 2000 ft. 200 15.

The heading is now 331 (instead of 339 with no wind). Is this what is expected?

Track (magnetic)  339
Wind  (from          200 (lower number))

Need to draw diagram on map

6 PRINT CURRENT PLAN

Initiates paper printout of the current plan. It is possible to change details such as airspeed, wind, magnetic variation etc. during this operation when requested if required.
Note that if the printer is not connected then the display of the printout will halt indicating this. Pressing  will effect a return to the main menu.

Note that Diamond and then the  key should be pressed after printout is complete to suspend the CLI on the Z88.

7 SAVE CURRENT PLAN

Initiates the save sequence requesting a name for the current plan to be saved under. Using the first three letters of the departure point together with the first three letters of the destination is one method of ordering your old plan names but any name may be used.

 7 Save Current Plan - Example

OX-WELLSB.SET and OX-WELLSB are generated.

8 RETURN TRIP PLAN

Selects the menu :

Imitates the sequence for the reverse flight plan trip, starting 'with the original destination point first. The details of airspeed, wind etc. may be changed when requested if required.

1 - Display Return Trip - Example

Select 1 Display Return Trip.

Check the route

Enter the current wind

Return route.

2 PRINT RETURN TRIP

Initiates the paper printout of the return trip plan. If the printer is not connected the display will halt after a few characters. Pressing  will return to the main menu.

2 NEW PLAN

Selection of this option initiates the formation of a new flight plan the operation is described above in this document.

3 OLD PLANS

To retrieve a stored plan select this option and enter the file name of the plan to be retrieved as requested. Note that the details of .airspeed, wind etc., used in the original plan will also be restored. When retrieved the old plan becomes the current plan and can be manipulated as any other current plan.

It is possible to view the file names of plans already stored.

This is achieved by typing ? at the file name prompt.

3 Old Plans - Example

Load previously saved plans here.

4 OTHER FUNCTIONS

SELECTING THIS OPTION CALLS THE FOLLOWING MENU

Two more functions are selected here.

5 Airfield Data Bases

There are 3 choices. The first two asks

1 ADD a NEW location

1. ADD a NEW location
This selects the menu:

1 Use Latitude & Longitude?

See Defining Waypoints for more details.

2 Use Relative Location?

See Defining Waypoints for more details.

Defining Waypoints

There are two ways of defining waypoints.

1. Use latitude & longitude

The sequence entered requests firstly the name of the location you wish to add to the data base. This should he a unique name you wish to refer to or in the case of a vor or ndh use the ident code. You are next requested to enter the latitude of the location. It is necessary to use the format indicated (123456N i.e. degrees minutes seconds first letter of North or South as appropriate) otherwise it is not possible to continue with the: process.

Next longitude is requested in the same format. This may have two or three digits in the degrees element and the first letter of East or West as appropriate.

 Finally the IDENT CODE is requested. There is no fixed format for this but the inbuilt data bases use the following convention: 

• If one exists, use the 4 letter airfield ident code
• If no code exists use the first 4 letters of the name
• If it is a vor or ndb give the frequency

Data required to add a new location are:-

• NEW WAYPOINT Name
• Latitude  (123456N)
• Longitude  (123456W)
• Ident (ABCD)

1 Use Latitudes & Longitudes? - Example

The positions of Airfields for example are given in Latitudes & Longitudes. These are found in the Aerodromes published in the UK AIP.

Local VORs are given on main Airfield sites.

** BRIZE NORTON
0,51:50.250N,001:50.150W,0F,W,000 A40 NORTHLEACH ROUNDABOUT VRP
** BRIZE NORTON (ENR 2.1)

2 Use Relative Locations? - Example

When using relative locations, to describe the waypoint, the following information is required.

• A KNOWN LOCATION that is in the database is chosen as a start point.
• The TRUE BEARING from the KNOWN LOCATION in DEGREES TRUE
• The DISTANCE between the WAYPOINT and the KNOWN LOCATION (in naut,mls)
• A UNIQUE NAME for this waypoint.
• An IDENT CODE for this WAYPOINT

The result is given in Latitudes & Longitudes and give a unique name. The example below shows an abstract location 10 nM, 30 degrees from Oxford.

2 UPDATE an EXISTING location.

Data required to update an existing location are the same as above:-

• NEW WAYPOINT Name
• Latitude  (123456N)
• Longitude  (123456W)
• Ident (ABCD)

This is the option used when the location already exists in the data base but some of its information has changed e.g. location or frequency etc. The subsequent menu selected is the same as for the ADD option If two entries with the same location name are made under UPDATE option the last one entered is used by the program i.e the most current entry is utilised. If two entries with the same location name are inadvertently made under the ADD option the later entry will not be accessed.

3 Advanced user options

Primarily intended for the more computer literate user the options called here should be used with care in particular the create option destroys any existing content of the file being created.

This following menu is displayed:

4 SHOW a Data base  ?

This option will display the content of a data base file.
Give the three letter file name and the content will be cycled through.

5 APPEND to existing database  ?

This option allows further locations to be added to the end of any data base file. Follow the instructions given these are as for the ADDITIONS option which In itself would be more normally used.

Name of Database to modify? (WAV). Select a database to use.

1 Use Latitude & Longitude?

See Defining Waypoints for more details.

2 Use Relative Location?

See Defining Waypoints for more details.

I HAVE NOT MANAGED TO MAKE THIS WORK.

6 CREATE a New Data Base  ?

This option allows the creation of independent data bases allowing the user to keep personalised data. A three letter file name must be used.

A location is then later accessed by first typing these three letters followed by a space and then the location name. Note that if a file name already exists the original contents will be lost using this option.

Example - Use the suggested file name.

Add a Record, or new entry - Example

Select 1 Use Latitudes & Longitudes

NORTHLEACH ROUNDABOUT

** BRIZE NORTON
0,51:50.250N,001:50.150W,0F,W,000 A40 NORTHLEACH ROUNDABOUT VRP
** BRIZE NORTON (ENR 2.1)

Enter Latitude and Longitude.

Select Y when the data is correct.

See Plan a Flight on using some of these functions.

6 Aircraft Functions

This option produces the following menu

1 CHECK LIST

There are no check lists stored initially.

This option allows you to create your own personalised check lists for aircraft. The list when viewed is produced one line at a time the item should be checked then you may move to the next item by pressing .

(1) RUN A CHECKLIST

Type the number 1 followed by pressing the  key to call this option.
The option requests the plane name under which you have stored the. Check list you wish to use. Items are stepped through one line at a time as they are checked off. (Press  to continue to the next item in the list.

Type the in file name (without the .CHK) For example - PA28

The first item to be checked is displayed.

Pressing the key displays the next item. This is repeated until the end of the list is reached. The program returns to the Main Menu.

(2) CREATE A NEW CHECKLIST

This option is called by typing the number 2 followed by pressing the  key.
First request is a plane name. You recall the list using this name so keep it short and one word only.
The first item in the list is then requested this should be typed in restricting it to one line only then press  to move on to the next item.

Using PA28 as the Name of plane creates a file name of PA28.CHK

Type the first item that need to be checked, followed by the key.

Type the next item that need to be checked, followed by the key.

When the list is complete press  at the item prompt without typing in anything else this will terminate the list. You may now use option 1 to recall the list using the plane name requested to call this particular list.
You may have a number of different checklists resident in this way.

Pressing  twice ends inputting the list and saves the file.

(3) EDIT AN EXISTING CHECKLIST

Type the in file name (without the .CHK)

This option is called by typing 3 and pressing the  key Each item line of the list is shown one at a time with the Options to insert, delete or accept an item are offered at each line of the check list. Use I,D or A for this at each line. Step through the list pressing A if the items are to be accepted.

The first item to be checked is displayed. Press

• (I) to insert
• (D) to delete
• (A) to accept

Pressing the key displays the next item. This is repeated until the end of the list is reached.

saves the updated data

leaves the data as it was before.

The program then returns to the Main Menu.

(4) TO EXIT

The program returns to the Main Menu.

2 WEIGHT & BALANCE

The manual states "Simply follow the menus for this option."

Lets see what this does with some data

Here is a table for Normal Loading

Enter data

The data from the table above is entered.

• Empty Weight (lbs)
• Datum (in)
• Oil Weight (lbs)
• Datum (in)
• Fuel - AVGAS (US Gallons)
• Datum (in)
• Front Passengers (lbs)
• Datum (in)
• Rear Passengers (lbs)
• Datum (in)
• Front Baggage (lbs)
• Datum (in)
• Rear Baggage (lbs)
• Datum (in)

Result

The following result from Pilot Companion was obtained. It is within the calculations obtained from the table.

Press <ENTER> to continue

The program returns to the Main Menu.

3 Density Altitude

Enter some valid entries

Calculate Density Altitude

Calculate True Airspeed

4 Descent Rate

Give Distance to Run  1

Give Rate of Descent  2

Quit  3

The program returns to the Main Menu.

Example

Plan a Flight

Let's go to AV8 restaurant at Kemble via Northleach Roundabout for lunch from Oxford.

Oxford - Kemble via Northleach Roundabout

Select

Select 2 New Plan

Point of departure OXFORD is found. NORTHLEACH ROUNDABOUT is not.

Select 2.

** BRIZE NORTON
0,51:50.250N,001:50.150W,0F,W,000 A40 NORTHLEACH ROUNDABOUT VRP
** BRIZE NORTON (ENR 2.1)

Enter Latitude and Longitude.

Select Y when the data is correct.

KEMBLE is not found

Enter another new way point for Kemble.

No more way points, press to continue,

To check headings, no wind data is entered,

 To save this plan see 7 Save Current Plan

Appendix

Files & Databases

The files that have been loaded into RAM.1 are as shown by the Filer.

To get some idea of what data is there, here is a Pipedream view of the data.

rev and temp are used for the current plan.

data.dbf(c) 1988ast

vor.dbf(c)1988ast

ABERDEEN

ADN

571215N

571838N

021155W

EGPD

ALDERNEY

494225N

021248W

EGJA

ANDREWSFIELD

515340N

002705E

EGSL